Good Deal PicksDeals for the United States
BlogSearch
Product guide

POWERTEC FE1380 Solder Fume Extractor, 120W, 138 CFM

POWERTEC FE1380 is a solder fume extractor with three-stage filtration, a listed 138 CFM airflow, and a nozzle intended for close-proximity capture. Its advertised range of uses includes soldering, laser engraving, 3D printing, and crafting, but the stated capture zone is only about 2 inches from the nozzle.

At a glance

  • Three-stage setup described as a pre-filter, HEPA filter, and activated carbon filter.
  • Listed airflow is 138 CFM (235 m³/h), with a stated effective capture zone of approximately 2 inches (5 cm) from the nozzle.
  • Manufacturer claims up to 4,000 hours of service life for the main carbon filter.
  • Included kit list specifies a 4 ft. duct, 5 ft. power cord, and nozzle.
Price
$220.99Save 15%

Reference price: $259.99

Price checked: Nov 19, 2026

View offer

Pros and cons

Pros

  • The supplied contents list includes several filter elements and a nozzle, so the basic extraction setup is represented in the package details.
  • The stated close-range capture zone gives buyers a practical placement reference for soldering and other small-workstation tasks.

Cons

  • The stated capture zone is narrow, so this is a close-source extractor rather than a broad-area air cleaner.

Technical specifications

5 specifications
Identity
BrandPOWERTEC
ModelPOWERTEC Solder Fume Extractor (FE1380)
Filtration and operation
Filter typeHEPA
Contaminants listeddust, odors
Noise level70 db

What to know before buying

Listing details to confirm

Listing details are inconsistent on noise, with 70 db listed in product details and below 70 dB or less than 60 dB stated in promotional copy. The claimed 99.97% purification rate and up-to-4,000-hour carbon-filter life are not accompanied by test conditions, and the 120W figure appears in the title without a separate technical detail entry. Treat these as listing claims rather than verified performance figures.

What’s in the box

Included
  • Body/motor, 1 (installed)
  • Pre-filters, 5 (1 installed)
  • Middle filter, 1 (installed)
  • Main filter, 1 (installed)
  • Duct, 1, 4 ft. long
  • Power cord, 1, 5 ft.
  • Nozzle, 1

Who is it for?

A good fit for

  • Hobbyists or bench users seeking nozzle-based fume capture close to soldering or craft work.
  • Buyers who want a unit advertised for soldering, laser engraving, and 3D printing with pre-filter, HEPA, and activated-carbon stages.

Less suited to

  • People needing an extractor to capture fumes from a distance, since the stated capture zone is approximately 2 inches (5 cm) from the nozzle.
  • Buyers who need a confirmed noise figure or independently documented filtration and filter-life performance.
POWERTEC FE1380 Solder Fume Extractor, 120W, 138 CFM · photo 2
Additional product photo 2

Frequently asked questions

How close should the nozzle be to the work?

The listing says the effective capture zone is approximately 2 inches (5 cm) from the nozzle, so it is intended for close-proximity placement.

What filtration stages are described?

The listing describes a pre-filter for larger particles, a HEPA filter for fine dust and smoke, and an activated-carbon filter for gases and odors.

What is included with the FE1380?

The manufacturer contents list includes the body and motor, five pre-filters, a middle filter, a main filter, a 4 ft. duct, a 5 ft. power cord, and a nozzle.

Is its noise level confirmed?

No single figure is consistent across the listing. Product details say 70 db, while promotional text gives below 70 dB and less than 60 dB, so confirm the expected operating noise before buying.

POWERTEC FE1380 Solder Fume Extractor, 120W, 138 CFM · photo 3
Additional product photo 3

Alternative options

Product details in Markdown