Good Deal PicksDeals for the United States
BlogSearch
Product guide

Polymaker Fiberon PA612-CF15 Nylon Filament, 1.75 mm, 1 kg

Polymaker Fiberon PA612-CF15 is carbon-fiber-reinforced nylon filament for functional 3D-printed parts. Its long-chain PA612 base is presented as less moisture-sensitive than PA6 and stronger than PA12, but it still needs dry handling and a wear-resistant nozzle.

At a glance

  • PA612 nylon reinforced with 15 wt% carbon fiber, aimed at rigid functional prints and tooling.
  • Manufacturer says it is less moisture-sensitive than PA6 while remaining hygroscopic.
  • The listed 175°C HDT applies after a specific annealing process and is not a continuous-use temperature guarantee.
  • Requires an all-metal hotend and a hardened steel or ruby nozzle according to the supplied printing guidance.
Price
$47.49Save 21%

Reference price: $59.99

Price checked: Nov 19, 2026

View offerAhead of Black FridayExplore the selection

Often bought together

Pros and cons

Pros

  • The supplied TDS claims lower moisture sensitivity than PA6-based nylon and stronger mechanical performance than PA12-based materials.
  • Annealing guidance includes a defined 175°C heat-deflection test result and a stated process.
  • The source gives practical printing guidance, including temperature ranges, nozzle material and storage humidity.

Cons

  • Still requires moisture control, and the suggested drying routine adds preparation before printing when filament has been exposed to ambient humidity.
  • A hardened steel or ruby nozzle is specified, so a standard nozzle may not suit this abrasive carbon-fiber-filled material.

Technical specifications

21 specifications
Identity
BrandPolymaker
ModelFG07003
Dimensions and installation
Weight listed1 kg
Materials and protection
Material listedNylon
Filament diameter1.75mm
ColorFiberon Pa612-cf15 Black
Reinforcement15 wt% carbon fiber
Printing and performance
Recommended nozzle temperature250–300°C
Build plate temperature40–50°C
Heat deflection temperature175°C at 0.45 MPa after annealing at 100°C for 16 hours
Dry X-Y tensile strength91.9 MPa
X-Y tensile strength after specified annealing and moisture conditioning83.1 MPa
Bending modulus (dry)4583
Bending modulus (wet)3888
Storage and printing humidity guidancebelow 20% relative humidity
Drying guidance100°C for 10 hours
Suggested print speedup to 300 mm/s
Hotend guidanceall-metal hotend
Nozzle guidancehardened steel or ruby nozzle
Cooling fan guidancecooling fan off
Heated chamber guidanceA heated chamber is not required under the TDS conditions.

What to know before buying

  • Performance figures are manufacturer claims. The 175°C HDT is measured after annealing at 100°C for 16 hours at 0.45 MPa, not a general continuous operating temperature. The up-to-300 mm/s speed is conditional on a tuned profile, and drying at 100°C for 10 hours is advised after ambient exposure or when print symptoms appear. Confirm printer compatibility with the all-metal hotend and wear-resistant nozzle guidance, and keep filament below 20% relative humidity during storage and printing.

Who is it for?

A good fit for

  • Users printing rigid functional parts, jigs, fixtures, tooling or engineering prototypes who can meet the filament's temperature and nozzle requirements.
  • Print setups where reduced moisture sensitivity relative to PA6 is useful, while still allowing for dry storage and handling.

Less suited to

  • Printers without an all-metal hotend or a hardened steel or ruby nozzle, based on the supplied printing guidance.
  • Users seeking a low-maintenance filament that can be stored or printed without humidity control.
Polymaker Fiberon PA612-CF15 Nylon Filament, 1.75 mm, 1 kg · photo 2
Additional product photo 2

Customer reviews on Amazon

4.7 / 5 · 43 ratings
  • 5 stars90%90%
  • 4 stars4%4%
  • 3 stars0%0%
  • 2 stars0%0%
  • 1 star6%6%

Aggregate ratings are strongly positive overall, with most ratings in the five-star category, but a small one-star share shows that experiences are not uniformly favorable. Without comment-level feedback, the ratings do not establish specific strengths or problems. For buyers, the practical question is whether their printer and drying routine can handle the stated nylon and carbon-fiber printing requirements.

Frequently asked questions

What printer setup does the supplied guidance call for?

It specifies an all-metal hotend, a 250–300°C nozzle, a 40–50°C build plate, and a hardened steel or ruby nozzle. The cooling fan should be off. Confirm your printer can meet those requirements.

Does this nylon need drying?

It remains hygroscopic despite being described as less moisture-sensitive than PA6. The guidance says to keep it below 20% relative humidity during storage and printing, and to dry it at 100°C for 10 hours after ambient exposure or if stringing, bubbles or rough surfaces appear.

What does the 175°C heat-deflection figure mean?

It is a listed HDT result at 0.45 MPa after annealing at 100°C for 16 hours. It should not be read as the continuous operating temperature for every printed part.

Is a heated chamber required?

The supplied TDS guidance says a heated chamber is not required under its stated conditions. Results can depend on the printer and tuned profile.

Polymaker Fiberon PA612-CF15 Nylon Filament, 1.75 mm, 1 kg · photo 3
Additional product photo 3

Alternative options

Products with discounts that might interest you

3.9
Skydo 952XL Compatible Ink Cartridge 4-Pack
Skydo 952XL Compatible Ink Cartridge 4-Pack

$106.99

$94.99

-11%
-11%
Product details in Markdown